高铝砖材料配比方法High - aluminum brick material rat

常见问题解答 | 阅读数:

轻质高铝砖公司排名

高铝砖的价格是多少? - 。

一般的高铝砖多少钱一吨?质量好坏怎么区分? 爱问知识人。

【云南高铝砖价格高铝砖价格质量】- 黄页88网。

质量保证 二级高铝标准砖热销价格品牌:振源河南新密-盖德...。

    制作高铝耐火砖一般选用软质粘土,这种材料具有较好的可塑性,因此制作高铝耐火砖一般选用软质粘土作分离剂。可是粘土中的游离SiO2与高铝矾土熟猜中的游离Al2O3在1200℃下发生二次莫来石化反应,发生较大的体缩短,硅的气孔率增大,强度下降。因此,配猜中粘土粉的参与量以不逾越5%为宜。
    此外,可选用高铝矾土微粉作分离剂;或将高铝矾土微粉与粘土粉按必定份额配制,制备组成莫来石作分离剂。用这些分离剂皆可制得无二次缩短的高铝砖。
    高铝砖泥料一般选用粗、中、细三级配料。粗颗粒上限一般为2~3mm,参与量为40%~50%(对于异型成品,粗颗粒上限可下降至2~1mm)1~0.1mm的中心颗粒参与量以10%~20%为宜;〈0.1mm的细粉参与量应控制在40%~50%。花费理论标明,恰当增大粗颗粒尺度和数量可前进泥料的堆积密度,且易于成型。烧成时,物料附近的二次莫来石化反应较弱,易于烧结。可是,扩大颗粒尺度也有必定极限。假设扩大到4~5mm,易发生缺边掉角现象,且安排安排平均水平遭到影响。所以,最大颗粒尺度以3mm为宜。
    配料中参与细粉有利于坯体烧结、添加成品的密度。因为细粉在烧结时发生的烧成缩短可以削弱或抵消二次莫来石化反应所发生的体积缩短,所以参与细粉甚为必要。可是,细粉参与量过多,不只成型困难,而且易发生裂纹,烧成缩短较大,废品率添加。因此,细粉参与量以40~50%为宜。
    中心颗粒既不起组颗粒的骨架效果,也不是细粉的烧结效果。因此,中心颗粒的参与量一般约束在最低数量。可是,不能悉数撤销中心颗粒。假设撤销,成品烧后易发生龟裂,外观质量欠好,而且给物料处置带来必定困难。一般说来,中心颗粒参与量以10%为宜。

    本公司长期出售高铝砖、粘土砖、磷酸盐砖、硅砖等,价格合理,质量优。联系电话:86-13608670776

Soft clay is generally used as the separation agent for the production of high aluminium refractory bricks, because this material has good plasticity.But free SiO2 in clay and free Al2O3 in high alumina ripe guess at 1200℃ secondary Mullite reaction occurred, the occurrence of a larger body shortened, the porosity of silicon increased, the strength decreased.Therefore, it is advisable not to exceed 5% in the amount of clay.

In addition, high bauxite powder can be used as separation agent.Or high bauxite powder and clay powder according to a certain proportion of preparation, preparation of mullite as a separation agent.High alumina brick without secondary shortening can be prepared by using these separators.

High aluminum brick mud material generally use coarse, medium, fine three ingredients.The upper limit of coarse particles is generally 2 ~ 3mm, and the participation amount is 40% ~ 50% (for special-shaped products, the upper limit of coarse particles can be reduced to 2 ~ 1mm). The participation amount of center particles of 1 ~ 0.1mm should be 10% ~ 20%.The amount of fine powder < 0.1mm should be controlled at 40% ~ 50%.The cost theory indicates that increasing the size and quantity of coarse particles can advance the accumulation density of the sludge and make it easy to form.The secondary mullite reaction near the material is weak and easy to be sintered.However, there is a certain limit to enlarging particle size.It is assumed that the phenomenon of missing edge and missing Angle is easy to occur when it is extended to 4 ~ 5mm, and the average level of arrangement is affected.Therefore, the maximum particle size should be 3mm.

It is beneficial to the sintering of billet and the density of finished product.Because the shrinkage of fine powder during sintering can attenuate or counteract the volume reduction in the secondary Mullite reaction, it is necessary to participate in fine powder.However, the amount of fine powder involved is too much, not only difficult to form, but also prone to crack, burning shorter, scrap rate added.Therefore, the amount of fine powder should be 40 ~ 50%.

The central particle has neither the skeletonization effect nor the sintering effect of fine powder.Therefore, the central particle participation is generally constrained to a minimum number.However, the center particles cannot be completely retracted.Assume to cancel, the finished product is easy to crack after burning, appearance quality is not good, and bring certain difficulty to material disposal.Generally speaking, the participation amount of center particles should be 10%.

Our company sells high aluminum brick, clay brick, phosphate brick, silicon brick and so on for a long time, with reasonable price and excellent quality.Contact number: 86-13608670776


------以上为辉煌耐火砖厂家为大家简述的常见问题解答的一些基本详情!本文章为辉煌耐材原创文章如需转载请注明版权------

湖南客户订购高铝砖已达

成功案例

145

印尼客户订购的高铝砖整

成功案例

181

水泥回转窑用耐火砖施工

成功案例

60

江苏一客户采购一级高铝

成功案例

176

收藏

赞  0

评论0  

展开    我有话说

0条评论

网友评论仅供其表达个人看法,并不表明本站立场。

友情链接 河南高铝砖|河北高铝砖| 湖南高铝砖| 湖北高铝砖| 江西高铝砖| 广东高铝砖| 广西高铝砖| 黑龙江高铝砖| 吉林高铝砖| 内蒙古高铝砖| 四川高铝砖| 甘肃高铝砖| 宁夏高铝砖| 陕西高铝砖| |